Modem & Data Protection (model dependent)
Protection is extended to your phone and network lines with the addition of RJ11 and RJ45 jacks
on the QPF unit, creating ideal protection for Fax/Internet/Network users. Power surges can pass
to the connected equipment through phone lines and network cables.
CAUTION
CAUTION
CAUTION
CAUTION
FEATURES
If you have any questions call us at our Tech Support line toll free
Use this user's guide for the following products:
1.Turn off and un-plug equipment to be protected from wall outlet.
2. Plug the equipment into the QPF .
3. Plug the QPF unit into grounded wall outlet.
4. Your equipment is now fully protected. Place the QPF where monitoring lights can be observed.
unit
Installation of TBF™
POS Guardian
Power Cord
Installation for Protection for Telephone Line and Network Cable
TELEPHONE
1. Unplug the equipment's telephone cable from the wall jack and plug into the RJ11 "DEVICE"
on the QPF.
2. Plug the provided telephone cable to the RJ11 jack "LINE" on the QPF.
3. Plug the other end of the telephone cable into the RJ11 wall jack.
CAUTION: - Never install telephone wiring during a lightning storm.
- Disconnect telephone line at the network interface before installing the secondary
protector.
- Intended for indoor use only.
Telephone Line Protection clamping voltage 250-350 vdc.
NETWORK
1. Unplug the equipment's network cable from the wall RJ45 network jack and plug into the RJ45
"DEVICE" on the QPF.
2. Plug the provided CAT5 cable to the RJ45 jack "LINE" on the QPF.
3. Plug the other end of the CAT5 cable into the wall RJ45 network jack. Your equipment is now
fully protected. Place the QPF where monitoring lights can be observed.
Use the Standard CAT 5 Network Patch cord when using the Network protection RJ45 circuit.
Connected
Equipment with
Tel./Modem Jack
Power Cord
Power Cord
Phone Cord
Phone Cord
Network Cord
Network Cord
LINE
LINE
DEVICE
DEVICE
Phone
Wall Jack
Network Jack/ HUB
Connected
Equipment with
Network Jack
The RED light indicates improper ground
connection or reversed power wires which
needs to be corrected.
The green light confirms properly the
connected equipment is fully protected.
GREEN LIGHT -
RED LIGHT -
MODEL / PART NUMBER DESCRIPTION
120V/15A, two outlets , Phone Protection (RJ11) +Network Protection (RJ45)
120V/15A, three outlets, Phone Protection (RJ11) +Network Protection (RJ45)
120V/20A, one pigtail outlet, Phone Protection (RJ11) +Network Protection (RJ45)
120V/20A, three outlets (1)20A and (2)15A, Phone Protection (RJ11)
+ Network Protection (RJ45)
• Use indoors only
• Avoid dropping the unit.
• Only plug the QPF into a three pronged grounded outlet.
This unit is not to be used with any type of ground “lift” or pin eliminator.
• Do not open the QPF unit, there are no serviceable parts
inside. Opening the unit will void your warranty.
This device features an internal protection that will disconnect the surge protective component
at the end of its useful life but will maintain power to the load now unprotected. If this situation
is undesirable for the application, follow the manufacturer's instructions for replacing the device.
Do not install this device if there is not at least 10 meters (30 feet) or more of wire between the
electrical outlet and the electrical service panel.
Risk of Electric Shock. Do not plug into another relocatable power tap.
IMPORTANT: If the RED Light comes on, contact your electrician to
inspect and correct the outlet wiring in order to receive the maximum
protection for your connected equipment.
QPF15-1121TN
QPF15-1131TN
QPF20-1211TN
QPF20-1231TN
(4 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels